18 - Ignition, samochody, TOYOTA COROLLA-MANUAL

18–1
IGNITION
–
IGNITION SYSTEM
IGNITION SYSTEM
ON–VEHICLE INSPECTION
NOTICE:
”Cold” and ”Hot” in these sentences express the temperature of the coils themselves. ”Cold” is from
–10
1804B–01
C (14
F) to 50
C (122
F) and ”Hot” is from 50
C (122
F) to 100
C (212
F).
1. INSPECT IGNITION COIL (WITH IGNITER) AND SPARK TEST
(a) Confirm DTC.
NOTICE:
If DTC is indicated, carry out troubleshooting in accordance with the procedure on the following DTC.
(b) Check that the spark occurs.
(1) Remove the ignition coils (with igniter).
(2) Using a 16 mm (0.63 in) plug wrench, remove the spark plugs.
(3) Install the spark plugs to each ignition coils (with igniter), and connect the ignition coil connectors.
(4) Disconnect the 4 injector connectors.
(5) Ground the spark plugs.
(6) Check if spark occurs while engine is being cranked.
NOTICE:
Replace the ignition coil when it is given an impact.
Do not crank the engine for more than 2 seconds.
HINT:
If the spark does not occur, do the test as follow.
(c) Using a 16 mm (0.63 in.) plug wrench, install the spark plugs.
Torque: 25 N
V
m (255 kgf
V
cm, 18 ft
V
lbf)
(d) Install the ignition coil with igniter.
Torque: 9.0 N
V
m (92 kgf
V
cm, 80 in.
lbf)
2004 COROLLA (RM1037U)
Author:
Date:
1207
Be sure to ground the spark plug, when checking.
V
18–2
IGNITION
–
IGNITION SYSTEM
INSPECTION
1804C–01
1. SPARK PLUG
NOTICE:
Never use a wire brush for cleaning.
Never attempt to adjust the electrode gap on used
spark plug.
Spark plug should be replaced every 192,000 km
(120,000 miles).
(a) Clean the spark plugs.
Air pressure: Below 588 kPa (6.0 kg/cm
2
, 85 psi)
Duration: 20 seconds or less
A50033
(b) Check the spark plug for thread damage and insulator
damage.
HINT:
If abnormal, replace the spark plug.
Recommended spark plug:
SK16R11 (DENSO made)
IFR5A11 (NGK made)
B01301
(c) Check the spark plug electrode gap.
Electrode gap: 1.1 mm (0.043 in.)
Electrode Gap
B02101
2. CRANK POSITION SENSOR NO.1
(a) Using an ohmmeter, measure the resistance between terminals.
RESISTANCE:
At cold 835 – 1,400
W
At hot 1,060 – 1,645
W
NOTICE:
”Cold” and ”Hot” on the table express the temperature of the coils themselves. ”Cold” is from –10
C
(14
F) to 50
C (122
F) and ”Hot” is from 50
C (122
F) to 100
C (212
F).
HINT:
If the resistance is not as specified, replace the crank position sensor No. 1.
2004 COROLLA (RM1037U)
Author:
Date:
1208
18–3
IGNITION
–
IGNITION SYSTEM
3. CRANK POSITION SENSOR
(a) Using an ohmmeter, measure the resistance between terminals.
RESISTANCE:
At cold 1,630 – 2,740
W
At hot 2,065 – 3,225
W
NOTICE:
”Cold” and ”Hot” on the table express the temperature of the coils themselves. ”Cold” is from –10
C
(14
F) to 50
C (122
F) and ”Hot” is from 50
C (122
F) to 100
C (212
F).
HINT:
If the resistance is not as specified, replace the crank position sensor.
4. IGNITION RELAY
(a) Continuity inspection.
(1) Using an ohmmeter, check that continuity exists be-
tween each terminal.
Specified condition:
Between terminal 1 and 2 Continuity
Between terminal 3 and 5 No continuity
(2) Using an ohmmeter, check that continuity exists be-
tween terminals 3 and 5 when the battery voltage is
applied across terminals 1 and 2.
E12471
2004 COROLLA (RM1037U)
Author:
Date:
1209

zanotowane.pl

doc.pisz.pl

pdf.pisz.pl

hannaeva.xlx.pl